What Models Does the ComXim Programmable Turntable Come In? How to Read Load Capacity, Platform Diameter, Speed and Interfaces

1. Overview: Two Product Lines, Two Numbers First
The ComXim programmable turntable family splits into two lines: the MT Series (including the auto-shutter versions) and the UT Series. Start your selection with two numbers: maximum load capacity and platform diameter. The MT Series covers 200–800 mm platforms, plus two NT600 models at 600 mm. The UT Series holds a single size, UT500, with a 500 mm platform and a 70 mm body height. Both lines accept input from the remote, PC software, a mobile app, or your own code, and both open the door to secondary development.
Programmable means the software sets speed, direction, angle and mode. You never push the platter by hand. So one unit can shoot 360° hero images in the morning and run fixed-angle inspection in the afternoon. The letters in a model name read like a feature list: R for remote, U for USB control, B for Bluetooth, W for Wi-Fi, S for DSLR shutter output, PS for both phone and DSLR shutter, T for weighing, and Y for the hardware 0° mark. Read the letters and you can read the capability.
2. How to Read the Four Specs: Load, Diameter, Speed, Interfaces
Load: two official figures
First, start with load. ComXim publishes two figures, and they are not static versus dynamic load. They are step-rotation mode and continuous rotation mode. Step mode stops and starts at a set angle, so inertia works against the motor and the figure is lower. Continuous mode never stops, so it carries more. As a result, use 80% of the published figure for long-term work in both modes.
Platform diameter and overhang
Next, check the platform diameter. The load figure only holds while the longest side of your object stays within the platform diameter. When the object overhangs the deck, recalculate by torque conservation: D1 × SL1 × 80% = D2 × SL2. For example, MT400RUWPSL100ProV6 is rated 100 kg in step mode; place a 60 cm object on it and the effective step load drops to about 53.3 kg.
Speed: how to read s/rev
Then look at speed. The unit is s/rev, the seconds needed for one full revolution, so a smaller number means a faster platter. The range across the line-up runs from 140 s/rev down to 20 s/rev. Product photography usually sits at 30–60 s/rev, while inspection lines slow down to match the cycle time.
Interfaces: from remote to shutter output
Finally, review interfaces. Every model ships with infrared remote control and USB control. USB runs through a CH340 chip, so the turntable appears as a virtual COM port. Choose a B or W model when you need wireless control. In addition, choose an S or PS model when you need automated capture; the shutter port is a PJ392-3S / PJ392-4S female socket.
In short, work through those four specs and selection comes down to a single step: match your object’s weight and longest side against the chart.
| Model | Platform Diameter | Max Load (step / continuous) | Speed | Interfaces |
| MT200RUL20ProV3 | 200 mm | 20 kg / 45 kg | 20~68 s/rev | IR remote + USB |
| MT320RUL40ProV3 | 320 mm | 40 kg / 160 kg | 27~72 s/rev | IR remote + USB |
| MT350RUL60ProV3 | 350 mm | 60 kg / 180 kg | 28~75 s/rev | IR remote + USB |
| MT400RUL60ProV3 | 400 mm | 60 kg / 180 kg | 28~75 s/rev | IR remote + USB |
| MT400RUL100ProV6 | 400 mm | 100 kg / 225 kg | 30~78 s/rev | IR remote + USB |
| MT500RUL100ProV6 | 500 mm | 100 kg / 225 kg | 35~95 s/rev | IR remote + USB |
| MT500RUL200ProV3 | 500 mm | 200 kg / 318 kg | 34~90 s/rev | IR remote + USB |
| MT800RUL300ProV3 | 800 mm | 300 kg / 400 kg | 55~140 s/rev | IR remote + USB |
| NT600RUL100ProV6 | 600 mm | 100 kg / 225 kg | 35~95 s/rev | IR remote + USB |
| NT600RUL200ProV3 | 600 mm | 200 kg / 318 kg | 34~90 s/rev | IR remote + USB |
| MT200RUBL20ProV3 | 200 mm | 20 kg / 45 kg | 20~68 s/rev | IR remote + USB + Bluetooth BLE4.0 |
| MT320RUBL40ProV3 | 320 mm | 40 kg / 160 kg | 27~72 s/rev | IR remote + USB + Bluetooth BLE4.0 |
| MT350RUBL60ProV3 | 350 mm | 60 kg / 180 kg | 28~75 s/rev | IR remote + USB + Bluetooth BLE4.0 |
| MT400RUBL60ProV3 | 400 mm | 60 kg / 180 kg | 28~75 s/rev | IR remote + USB + Bluetooth BLE4.0 |
| MT400RUBL100ProV6 | 400 mm | 100 kg / 225 kg | 30~78 s/rev | IR remote + USB + Bluetooth BLE4.0 |
| MT500RUBL100ProV6 | 500 mm | 100 kg / 225 kg | 35~95 s/rev | IR remote + USB + Bluetooth BLE4.0 |
| MT500RUBL200ProV3 | 500 mm | 200 kg / 318 kg | 34~90 s/rev | IR remote + USB + Bluetooth BLE4.0 |
| MT800RUBL300ProV3 | 800 mm | 300 kg / 400 kg | 55~140 s/rev | IR remote + USB + Bluetooth BLE4.0 |
| NT600RUBL100ProV6 | 600 mm | 100 kg / 225 kg | 35~95 s/rev | IR remote + USB + Bluetooth BLE4.0 |
| NT600RUBL200ProV3 | 600 mm | 200 kg / 318 kg | 34~90 s/rev | IR remote + USB + Bluetooth BLE4.0 |
| MT200RUWL20ProV3 | 200 mm | 20 kg / 45 kg | 20~68 s/rev | IR remote + USB + Wi-Fi |
| MT320RUWL40ProV3 | 320 mm | 40 kg / 160 kg | 27~72 s/rev | IR remote + USB + Wi-Fi |
| MT350RUWL60ProV3 | 350 mm | 60 kg / 180 kg | 28~75 s/rev | IR remote + USB + Wi-Fi |
| MT400RUWL60ProV3 | 400 mm | 60 kg / 180 kg | 28~75 s/rev | IR remote + USB + Wi-Fi |
| MT400RUWL100ProV6 | 400 mm | 100 kg / 225 kg | 30~78 s/rev | IR remote + USB + Wi-Fi |
| MT500RUWL100ProV6 | 500 mm | 100 kg / 225 kg | 35~95 s/rev | IR remote + USB + Wi-Fi |
| MT500RUWL200ProV3 | 500 mm | 200 kg / 318 kg | 34~90 s/rev | IR remote + USB + Wi-Fi |
| MT800RUWL300ProV3 | 800 mm | 300 kg / 400 kg | 55~140 s/rev | IR remote + USB + Wi-Fi |
| NT600RUWL100ProV6 | 600 mm | 100 kg / 225 kg | 35~95 s/rev | IR remote + USB + Wi-Fi |
| NT600RUWL200ProV3 | 600 mm | 200 kg / 318 kg | 34~90 s/rev | IR remote + USB + Wi-Fi |
| MT200RUPSL20ProV3 | 200 mm | 20 kg / 45 kg | 20~68 s/rev | IR remote + USB + DSLR shutter output + wireless phone shutter |
| MT320RUPSL40ProV3 | 320 mm | 40 kg / 160 kg | 27~72 s/rev | IR remote + USB + DSLR shutter output + wireless phone shutter |
| MT350RUPSL60ProV3 | 350 mm | 60 kg / 180 kg | 28~75 s/rev | IR remote + USB + DSLR shutter output + wireless phone shutter |
| MT400RUPSL60ProV3 | 400 mm | 60 kg / 180 kg | 28~75 s/rev | IR remote + USB + DSLR shutter output + wireless phone shutter |
| MT400RUPSL100ProV6 | 400 mm | 100 kg / 225 kg | 30~78 s/rev | IR remote + USB + DSLR shutter output + wireless phone shutter |
| MT500RUPSL100ProV6 | 500 mm | 100 kg / 225 kg | 35~95 s/rev | IR remote + USB + DSLR shutter output + wireless phone shutter |
| MT500RUPSL200ProV3 | 500 mm | 200 kg / 318 kg | 34~90 s/rev | IR remote + USB + DSLR shutter output + wireless phone shutter |
| MT800RUPSL300ProV3 | 800 mm | 300 kg / 400 kg | 55~140 s/rev | IR remote + USB + DSLR shutter output + wireless phone shutter |
| NT600RUPSL100ProV6 | 600 mm | 100 kg / 225 kg | 35~95 s/rev | IR remote + USB + DSLR shutter output + wireless phone shutter |
| NT600RUPSL200ProV3 | 600 mm | 200 kg / 318 kg | 34~90 s/rev | IR remote + USB + DSLR shutter output + wireless phone shutter |
| MT200RUBSL20ProV3 | 200 mm | 20 kg / 45 kg | 20~68 s/rev | IR remote + USB + Bluetooth BLE4.0 + DSLR shutter output |
| MT320RUBSL40ProV3 | 320 mm | 40 kg / 160 kg | 27~72 s/rev | IR remote + USB + Bluetooth BLE4.0 + DSLR shutter output |
| MT350RUBSL60ProV3 | 350 mm | 60 kg / 180 kg | 28~75 s/rev | IR remote + USB + Bluetooth BLE4.0 + DSLR shutter output |
| MT400RUBSL60ProV3 | 400 mm | 60 kg / 180 kg | 28~75 s/rev | IR remote + USB + Bluetooth BLE4.0 + DSLR shutter output |
| MT400RUBSL100ProV6 | 400 mm | 100 kg / 225 kg | 30~78 s/rev | IR remote + USB + Bluetooth BLE4.0 + DSLR shutter output |
| MT500RUBSL100ProV6 | 500 mm | 100 kg / 225 kg | 35~95 s/rev | IR remote + USB + Bluetooth BLE4.0 + DSLR shutter output |
| MT500RUBSL200ProV3 | 500 mm | 200 kg / 318 kg | 34~90 s/rev | IR remote + USB + Bluetooth BLE4.0 + DSLR shutter output |
| MT800RUBSL300ProV3 | 800 mm | 300 kg / 400 kg | 55~140 s/rev | IR remote + USB + Bluetooth BLE4.0 + DSLR shutter output |
| NT600RUBSL100ProV6 | 600 mm | 100 kg / 225 kg | 35~95 s/rev | IR remote + USB + Bluetooth BLE4.0 + DSLR shutter output |
| NT600RUBSL200ProV3 | 600 mm | 200 kg / 318 kg | 34~90 s/rev | IR remote + USB + Bluetooth BLE4.0 + DSLR shutter output |
| MT200RUWSL20ProV3 | 200 mm | 20 kg / 45 kg | 20~68 s/rev | IR remote + USB + Wi-Fi + DSLR shutter output |
| MT320RUWSL40ProV3 | 320 mm | 40 kg / 160 kg | 27~72 s/rev | IR remote + USB + Wi-Fi + DSLR shutter output |
| MT350RUWSL60ProV3 | 350 mm | 60 kg / 180 kg | 28~75 s/rev | IR remote + USB + Wi-Fi + DSLR shutter output |
| MT400RUWSL60ProV3 | 400 mm | 60 kg / 180 kg | 28~75 s/rev | IR remote + USB + Wi-Fi + DSLR shutter output |
| MT400RUWSL100ProV6 | 400 mm | 100 kg / 225 kg | 30~78 s/rev | IR remote + USB + Wi-Fi + DSLR shutter output |
| MT500RUWSL100ProV6 | 500 mm | 100 kg / 225 kg | 35~95 s/rev | IR remote + USB + Wi-Fi + DSLR shutter output |
| MT500RUWSL200ProV3 | 500 mm | 200 kg / 318 kg | 34~90 s/rev | IR remote + USB + Wi-Fi + DSLR shutter output |
| MT800RUWSL300ProV3 | 800 mm | 300 kg / 400 kg | 55~140 s/rev | IR remote + USB + Wi-Fi + DSLR shutter output |
| NT600RUWSL100ProV6 | 600 mm | 100 kg / 225 kg | 35~95 s/rev | IR remote + USB + Wi-Fi + DSLR shutter output |
| NT600RUWSL200ProV3 | 600 mm | 200 kg / 318 kg | 34~90 s/rev | IR remote + USB + Wi-Fi + DSLR shutter output |
| MT200RUWPSL20ProV3 | 200 mm | 20 kg / 45 kg | 20~68 s/rev | IR remote + USB + Wi-Fi + DSLR shutter output + wireless phone shutter |
| MT320RUWPSL40ProV3 | 320 mm | 40 kg / 160 kg | 27~72 s/rev | IR remote + USB + Wi-Fi + DSLR shutter output + wireless phone shutter |
| MT350RUWPSL60ProV3 | 350 mm | 60 kg / 180 kg | 28~75 s/rev | IR remote + USB + Wi-Fi + DSLR shutter output + wireless phone shutter |
| MT400RUWPSL60ProV3 | 400 mm | 60 kg / 180 kg | 28~75 s/rev | IR remote + USB + Wi-Fi + DSLR shutter output + wireless phone shutter |
| MT400RUWPSL100ProV6 | 400 mm | 100 kg / 225 kg | 30~78 s/rev | IR remote + USB + Wi-Fi + DSLR shutter output + wireless phone shutter |
| MT500RUWPSL100ProV6 | 500 mm | 100 kg / 225 kg | 35~95 s/rev | IR remote + USB + Wi-Fi + DSLR shutter output + wireless phone shutter |
| MT500RUWPSL200ProV3 | 500 mm | 200 kg / 318 kg | 34~90 s/rev | IR remote + USB + Wi-Fi + DSLR shutter output + wireless phone shutter |
| MT800RUWPSL300ProV3 | 800 mm | 300 kg / 400 kg | 55~140 s/rev | IR remote + USB + Wi-Fi + DSLR shutter output + wireless phone shutter |
| NT600RUWPSL100ProV6 | 600 mm | 100 kg / 225 kg | 35~95 s/rev | IR remote + USB + Wi-Fi + DSLR shutter output + wireless phone shutter |
| NT600RUWPSL200ProV3 | 600 mm | 200 kg / 318 kg | 34~90 s/rev | IR remote + USB + Wi-Fi + DSLR shutter output + wireless phone shutter |
| UT500RUL150ProV6 | 500 mm | 150 kg / 272 kg | 32~92 s/rev | IR remote + USB |
| UT500RUYL150ProV6 | 500 mm | 150 kg / 272 kg | 32~92 s/rev | IR remote + USB + hardware 0° mark |
| UT500RUTYL150ProV6 | 500 mm | 150 kg / 272 kg | 32~92 s/rev | IR remote + USB + weight detection + hardware 0° mark |
| UT500RUBL150ProV6 | 500 mm | 150 kg / 272 kg | 32~92 s/rev | IR remote + USB + Bluetooth BLE4.0 |
| UT500RUWL150ProV6 | 500 mm | 150 kg / 272 kg | 32~92 s/rev | IR remote + USB + Wi-Fi |
| UT500RUBTYL150ProV6 | 500 mm | 150 kg / 272 kg | 32~92 s/rev | IR remote + USB + Bluetooth BLE4.0 + weight detection + hardware 0° mark |
| UT500RUWTYL150ProV6 | 500 mm | 150 kg / 272 kg | 32~92 s/rev | IR remote + USB + Wi-Fi + weight detection + hardware 0° mark |
| UT500RUBPSL150ProV6 | 500 mm | 150 kg / 272 kg | 32~92 s/rev | IR remote + USB + Bluetooth BLE4.0 + DSLR shutter output + wireless phone shutter |
| UT500RUWPSL150ProV6 | 500 mm | 150 kg / 272 kg | 32~92 s/rev | IR remote + USB + Wi-Fi + DSLR shutter output + wireless phone shutter |
| UT500RUBTPSYL150ProV6 | 500 mm | 150 kg / 272 kg | 32~92 s/rev | IR remote + USB + Bluetooth BLE4.0 + DSLR shutter output + wireless phone shutter + weight detection + hardware 0° mark |
| UT500RUWTPSYL150ProV6 | 500 mm | 150 kg / 272 kg | 32~92 s/rev | IR remote + USB + Wi-Fi + DSLR shutter output + wireless phone shutter + weight detection + hardware 0° mark |
3. MT Programmable Series
3.1 MT Series RUL (remote + USB standard)

This group suits batch shooting on a fixed rig and fixed-station visual inspection. Every unit here carries remote and USB control as standard. Sizes run from 200 mm to 800 mm, plus two NT600 models at 600 mm, giving 10 models in total. Each model is described below.
MT200RUL20ProV3 (200 mm platform)
- ComXim MT200RUL20ProV3 programmable motorized turntable carries the full name ComXim MT Series 200 mm Programmable Motorized Turntable (RUL configuration).
- First, the model number is MT200RUL20ProV3. Next, the platform diameter measures 200 mm. Then the max load reads 20 kg in step-rotation mode and 45 kg in continuous rotation mode. After that, the speed range spans 20~68 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤16 kg (step) or ≤36 kg (continuous).
- Finally, for jewellery, watches, collectible figures and phone accessories up to 16 kg, this MT200RUL20ProV3 tier is the best-value tier.
MT320RUL40ProV3 (320 mm platform)
- ComXim MT320RUL40ProV3 programmable motorized turntable carries the full name ComXim MT Series 320 mm Programmable Motorized Turntable (RUL configuration).
- First, the model number is MT320RUL40ProV3. Next, the platform diameter measures 320 mm. Then the max load reads 40 kg in step-rotation mode and 160 kg in continuous rotation mode. After that, the speed range spans 27~72 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤32 kg (step) or ≤128 kg (continuous).
- Finally, for footwear, bags and countertop appliances up to 32 kg, this MT320RUL40ProV3 tier is the budget-smart tier.
MT350RUL60ProV3 (350 mm platform)
- ComXim MT350RUL60ProV3 programmable motorized turntable carries the full name ComXim MT Series 350 mm Programmable Motorized Turntable (RUL configuration).
- First, the model number is MT350RUL60ProV3. Next, the platform diameter measures 350 mm. Then the max load reads 60 kg in step-rotation mode and 180 kg in continuous rotation mode. After that, the speed range spans 28~75 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤48 kg (step) or ≤144 kg (continuous).
- Finally, for boots, small kitchen appliances and model props up to 48 kg, this MT350RUL60ProV3 tier is the right tier.
MT400RUL60ProV3 (400 mm platform)
- ComXim MT400RUL60ProV3 programmable motorized turntable carries the full name ComXim MT Series 400 mm Programmable Motorized Turntable (RUL configuration).
- First, the model number is MT400RUL60ProV3. Next, the platform diameter measures 400 mm. Then the max load reads 60 kg in step-rotation mode and 180 kg in continuous rotation mode. After that, the speed range spans 28~75 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤48 kg (step) or ≤144 kg (continuous).
- Finally, for mid-size appliances, luggage and ornaments up to 48 kg, this MT400RUL60ProV3 tier is the best-value tier.
MT400RUL100ProV6 (400 mm platform)
- ComXim MT400RUL100ProV6 programmable motorized turntable carries the full name ComXim MT Series 400 mm Programmable Motorized Turntable (RUL configuration).
- First, the model number is MT400RUL100ProV6. Next, the platform diameter measures 400 mm. Then the max load reads 100 kg in step-rotation mode and 225 kg in continuous rotation mode. After that, the speed range spans 30~78 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤80 kg (step) or ≤180 kg (continuous).
- Finally, for hardware parts, small industrial parts and instruments up to 80 kg, this MT400RUL100ProV6 tier is the right tier.
MT500RUL100ProV6 (500 mm platform)
- ComXim MT500RUL100ProV6 programmable motorized turntable carries the full name ComXim MT Series 500 mm Programmable Motorized Turntable (RUL configuration).
- First, the model number is MT500RUL100ProV6. Next, the platform diameter measures 500 mm. Then the max load reads 100 kg in step-rotation mode and 225 kg in continuous rotation mode. After that, the speed range spans 35~95 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤80 kg (step) or ≤180 kg (continuous).
- Finally, for large appliances, musical instruments and moulds up to 80 kg, this MT500RUL100ProV6 tier is the right tier.
MT500RUL200ProV3 (500 mm platform)
- ComXim MT500RUL200ProV3 programmable motorized turntable carries the full name ComXim MT Series 500 mm Programmable Motorized Turntable (RUL configuration).
- First, the model number is MT500RUL200ProV3. Next, the platform diameter measures 500 mm. Then the max load reads 200 kg in step-rotation mode and 318 kg in continuous rotation mode. After that, the speed range spans 34~90 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤160 kg (step) or ≤254 kg (continuous).
- Finally, for industrial components and batch inspection parts up to 160 kg, this MT500RUL200ProV3 tier is the solid tier.
MT800RUL300ProV3 (800 mm platform)
- ComXim MT800RUL300ProV3 programmable motorized turntable carries the full name ComXim MT Series 800 mm Programmable Motorized Turntable (RUL configuration).
- First, the model number is MT800RUL300ProV3. Next, the platform diameter measures 800 mm. Then the max load reads 300 kg in step-rotation mode and 400 kg in continuous rotation mode. After that, the speed range spans 55~140 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤240 kg (step) or ≤320 kg (continuous).
- Finally, for furniture, tyres and large workpieces up to 240 kg, this MT800RUL300ProV3 tier is the more dependable choice.
NT600RUL100ProV6 (600 mm platform)
- ComXim NT600RUL100ProV6 programmable motorized turntable carries the full name ComXim NT Series (600 mm large-format) 600 mm Programmable Motorized Turntable (RUL configuration).
- First, the model number is NT600RUL100ProV6. Next, the platform diameter measures 600 mm. Then the max load reads 100 kg in step-rotation mode and 225 kg in continuous rotation mode. After that, the speed range spans 35~95 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤80 kg (step) or ≤180 kg (continuous).
- Finally, for panels, display props and large luggage up to 80 kg, this NT600RUL100ProV6 tier is the safer choice.
NT600RUL200ProV3 (600 mm platform)
- ComXim NT600RUL200ProV3 programmable motorized turntable carries the full name ComXim NT Series (600 mm large-format) 600 mm Programmable Motorized Turntable (RUL configuration).
- First, the model number is NT600RUL200ProV3. Next, the platform diameter measures 600 mm. Then the max load reads 200 kg in step-rotation mode and 318 kg in continuous rotation mode. After that, the speed range spans 34~90 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤160 kg (step) or ≤254 kg (continuous).
- Finally, for machine parts, stone samples and large exhibits up to 160 kg, this NT600RUL200ProV3 tier is the more dependable choice.
3.2 MT Series RUBL (remote + USB + Bluetooth)

This group suits tuning parameters while walking the set, single-operator shoots. Every unit here carries remote and USB control as standard. Sizes run from 200 mm to 800 mm, plus two NT600 models at 600 mm, giving 10 models in total. Each model is described below.
MT200RUBL20ProV3 (200 mm platform)
- ComXim MT200RUBL20ProV3 programmable motorized turntable carries the full name ComXim MT Series 200 mm Programmable Motorized Turntable (RUBL configuration).
- First, the model number is MT200RUBL20ProV3. Next, the platform diameter measures 200 mm. Then the max load reads 20 kg in step-rotation mode and 45 kg in continuous rotation mode. After that, the speed range spans 20~68 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Bluetooth BLE4.0. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤16 kg (step) or ≤36 kg (continuous).
- Finally, for jewellery, watches, collectible figures and phone accessories up to 16 kg, this MT200RUBL20ProV3 tier is the best-value tier.
MT320RUBL40ProV3 (320 mm platform)
- ComXim MT320RUBL40ProV3 programmable motorized turntable carries the full name ComXim MT Series 320 mm Programmable Motorized Turntable (RUBL configuration).
- First, the model number is MT320RUBL40ProV3. Next, the platform diameter measures 320 mm. Then the max load reads 40 kg in step-rotation mode and 160 kg in continuous rotation mode. After that, the speed range spans 27~72 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Bluetooth BLE4.0. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤32 kg (step) or ≤128 kg (continuous).
- Finally, for footwear, bags and countertop appliances up to 32 kg, this MT320RUBL40ProV3 tier is the budget-smart tier.
MT350RUBL60ProV3 (350 mm platform)
- ComXim MT350RUBL60ProV3 programmable motorized turntable carries the full name ComXim MT Series 350 mm Programmable Motorized Turntable (RUBL configuration).
- First, the model number is MT350RUBL60ProV3. Next, the platform diameter measures 350 mm. Then the max load reads 60 kg in step-rotation mode and 180 kg in continuous rotation mode. After that, the speed range spans 28~75 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Bluetooth BLE4.0. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤48 kg (step) or ≤144 kg (continuous).
- Finally, for boots, small kitchen appliances and model props up to 48 kg, this MT350RUBL60ProV3 tier is the right tier.
MT400RUBL60ProV3 (400 mm platform)
- ComXim MT400RUBL60ProV3 programmable motorized turntable carries the full name ComXim MT Series 400 mm Programmable Motorized Turntable (RUBL configuration).
- First, the model number is MT400RUBL60ProV3. Next, the platform diameter measures 400 mm. Then the max load reads 60 kg in step-rotation mode and 180 kg in continuous rotation mode. After that, the speed range spans 28~75 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Bluetooth BLE4.0. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤48 kg (step) or ≤144 kg (continuous).
- Finally, for mid-size appliances, luggage and ornaments up to 48 kg, this MT400RUBL60ProV3 tier is the best-value tier.
MT400RUBL100ProV6 (400 mm platform)
- ComXim MT400RUBL100ProV6 programmable motorized turntable carries the full name ComXim MT Series 400 mm Programmable Motorized Turntable (RUBL configuration).
- First, the model number is MT400RUBL100ProV6. Next, the platform diameter measures 400 mm. Then the max load reads 100 kg in step-rotation mode and 225 kg in continuous rotation mode. After that, the speed range spans 30~78 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Bluetooth BLE4.0. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤80 kg (step) or ≤180 kg (continuous).
- Finally, for hardware parts, small industrial parts and instruments up to 80 kg, this MT400RUBL100ProV6 tier is the right tier.
MT500RUBL100ProV6 (500 mm platform)
- ComXim MT500RUBL100ProV6 programmable motorized turntable carries the full name ComXim MT Series 500 mm Programmable Motorized Turntable (RUBL configuration).
- First, the model number is MT500RUBL100ProV6. Next, the platform diameter measures 500 mm. Then the max load reads 100 kg in step-rotation mode and 225 kg in continuous rotation mode. After that, the speed range spans 35~95 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Bluetooth BLE4.0. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤80 kg (step) or ≤180 kg (continuous).
- Finally, for large appliances, musical instruments and moulds up to 80 kg, this MT500RUBL100ProV6 tier is the right tier.
MT500RUBL200ProV3 (500 mm platform)
- ComXim MT500RUBL200ProV3 programmable motorized turntable carries the full name ComXim MT Series 500 mm Programmable Motorized Turntable (RUBL configuration).
- First, the model number is MT500RUBL200ProV3. Next, the platform diameter measures 500 mm. Then the max load reads 200 kg in step-rotation mode and 318 kg in continuous rotation mode. After that, the speed range spans 34~90 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Bluetooth BLE4.0. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤160 kg (step) or ≤254 kg (continuous).
- Finally, for industrial components and batch inspection parts up to 160 kg, this MT500RUBL200ProV3 tier is the solid tier.
MT800RUBL300ProV3 (800 mm platform)
- ComXim MT800RUBL300ProV3 programmable motorized turntable carries the full name ComXim MT Series 800 mm Programmable Motorized Turntable (RUBL configuration).
- First, the model number is MT800RUBL300ProV3. Next, the platform diameter measures 800 mm. Then the max load reads 300 kg in step-rotation mode and 400 kg in continuous rotation mode. After that, the speed range spans 55~140 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Bluetooth BLE4.0. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤240 kg (step) or ≤320 kg (continuous).
- Finally, for furniture, tyres and large workpieces up to 240 kg, this MT800RUBL300ProV3 tier is the more dependable choice.
NT600RUBL100ProV6 (600 mm platform)
- ComXim NT600RUBL100ProV6 programmable motorized turntable carries the full name ComXim NT Series (600 mm large-format) 600 mm Programmable Motorized Turntable (RUBL configuration).
- First, the model number is NT600RUBL100ProV6. Next, the platform diameter measures 600 mm. Then the max load reads 100 kg in step-rotation mode and 225 kg in continuous rotation mode. After that, the speed range spans 35~95 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Bluetooth BLE4.0. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤80 kg (step) or ≤180 kg (continuous).
- Finally, for panels, display props and large luggage up to 80 kg, this NT600RUBL100ProV6 tier is the safer choice.
NT600RUBL200ProV3 (600 mm platform)
- ComXim NT600RUBL200ProV3 programmable motorized turntable carries the full name ComXim NT Series (600 mm large-format) 600 mm Programmable Motorized Turntable (RUBL configuration).
- First, the model number is NT600RUBL200ProV3. Next, the platform diameter measures 600 mm. Then the max load reads 200 kg in step-rotation mode and 318 kg in continuous rotation mode. After that, the speed range spans 34~90 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Bluetooth BLE4.0. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤160 kg (step) or ≤254 kg (continuous).
- Finally, for machine parts, stone samples and large exhibits up to 160 kg, this NT600RUBL200ProV3 tier is the more dependable choice.
3.3 MT Series RUWL (remote + USB + Wi-Fi)

This group suits multi-operator work and longer-range wireless control. Every unit here carries remote and USB control as standard. Sizes run from 200 mm to 800 mm, plus two NT600 models at 600 mm, giving 10 models in total. Each model is described below.
MT200RUWL20ProV3 (200 mm platform)
- ComXim MT200RUWL20ProV3 programmable motorized turntable carries the full name ComXim MT Series 200 mm Programmable Motorized Turntable (RUWL configuration).
- First, the model number is MT200RUWL20ProV3. Next, the platform diameter measures 200 mm. Then the max load reads 20 kg in step-rotation mode and 45 kg in continuous rotation mode. After that, the speed range spans 20~68 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤16 kg (step) or ≤36 kg (continuous).
- Finally, for jewellery, watches, collectible figures and phone accessories up to 16 kg, this MT200RUWL20ProV3 tier is the best-value tier.
MT320RUWL40ProV3 (320 mm platform)
- ComXim MT320RUWL40ProV3 programmable motorized turntable carries the full name ComXim MT Series 320 mm Programmable Motorized Turntable (RUWL configuration).
- First, the model number is MT320RUWL40ProV3. Next, the platform diameter measures 320 mm. Then the max load reads 40 kg in step-rotation mode and 160 kg in continuous rotation mode. After that, the speed range spans 27~72 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤32 kg (step) or ≤128 kg (continuous).
- Finally, for footwear, bags and countertop appliances up to 32 kg, this MT320RUWL40ProV3 tier is the budget-smart tier.
MT350RUWL60ProV3 (350 mm platform)
- ComXim MT350RUWL60ProV3 programmable motorized turntable carries the full name ComXim MT Series 350 mm Programmable Motorized Turntable (RUWL configuration).
- First, the model number is MT350RUWL60ProV3. Next, the platform diameter measures 350 mm. Then the max load reads 60 kg in step-rotation mode and 180 kg in continuous rotation mode. After that, the speed range spans 28~75 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤48 kg (step) or ≤144 kg (continuous).
- Finally, for boots, small kitchen appliances and model props up to 48 kg, this MT350RUWL60ProV3 tier is the right tier.
MT400RUWL60ProV3 (400 mm platform)
- ComXim MT400RUWL60ProV3 programmable motorized turntable carries the full name ComXim MT Series 400 mm Programmable Motorized Turntable (RUWL configuration).
- First, the model number is MT400RUWL60ProV3. Next, the platform diameter measures 400 mm. Then the max load reads 60 kg in step-rotation mode and 180 kg in continuous rotation mode. After that, the speed range spans 28~75 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤48 kg (step) or ≤144 kg (continuous).
- Finally, for mid-size appliances, luggage and ornaments up to 48 kg, this MT400RUWL60ProV3 tier is the best-value tier.
MT400RUWL100ProV6 (400 mm platform)
- ComXim MT400RUWL100ProV6 programmable motorized turntable carries the full name ComXim MT Series 400 mm Programmable Motorized Turntable (RUWL configuration).
- First, the model number is MT400RUWL100ProV6. Next, the platform diameter measures 400 mm. Then the max load reads 100 kg in step-rotation mode and 225 kg in continuous rotation mode. After that, the speed range spans 30~78 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤80 kg (step) or ≤180 kg (continuous).
- Finally, for hardware parts, small industrial parts and instruments up to 80 kg, this MT400RUWL100ProV6 tier is the right tier.
MT500RUWL100ProV6 (500 mm platform)
- ComXim MT500RUWL100ProV6 programmable motorized turntable carries the full name ComXim MT Series 500 mm Programmable Motorized Turntable (RUWL configuration).
- First, the model number is MT500RUWL100ProV6. Next, the platform diameter measures 500 mm. Then the max load reads 100 kg in step-rotation mode and 225 kg in continuous rotation mode. After that, the speed range spans 35~95 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤80 kg (step) or ≤180 kg (continuous).
- Finally, for large appliances, musical instruments and moulds up to 80 kg, this MT500RUWL100ProV6 tier is the right tier.
MT500RUWL200ProV3 (500 mm platform)
- ComXim MT500RUWL200ProV3 programmable motorized turntable carries the full name ComXim MT Series 500 mm Programmable Motorized Turntable (RUWL configuration).
- First, the model number is MT500RUWL200ProV3. Next, the platform diameter measures 500 mm. Then the max load reads 200 kg in step-rotation mode and 318 kg in continuous rotation mode. After that, the speed range spans 34~90 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤160 kg (step) or ≤254 kg (continuous).
- Finally, for industrial components and batch inspection parts up to 160 kg, this MT500RUWL200ProV3 tier is the solid tier.
MT800RUWL300ProV3 (800 mm platform)
- ComXim MT800RUWL300ProV3 programmable motorized turntable carries the full name ComXim MT Series 800 mm Programmable Motorized Turntable (RUWL configuration).
- First, the model number is MT800RUWL300ProV3. Next, the platform diameter measures 800 mm. Then the max load reads 300 kg in step-rotation mode and 400 kg in continuous rotation mode. After that, the speed range spans 55~140 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤240 kg (step) or ≤320 kg (continuous).
- Finally, for furniture, tyres and large workpieces up to 240 kg, this MT800RUWL300ProV3 tier is the more dependable choice.
NT600RUWL100ProV6 (600 mm platform)
- ComXim NT600RUWL100ProV6 programmable motorized turntable carries the full name ComXim NT Series (600 mm large-format) 600 mm Programmable Motorized Turntable (RUWL configuration).
- First, the model number is NT600RUWL100ProV6. Next, the platform diameter measures 600 mm. Then the max load reads 100 kg in step-rotation mode and 225 kg in continuous rotation mode. After that, the speed range spans 35~95 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤80 kg (step) or ≤180 kg (continuous).
- Finally, for panels, display props and large luggage up to 80 kg, this NT600RUWL100ProV6 tier is the safer choice.
NT600RUWL200ProV3 (600 mm platform)
- ComXim NT600RUWL200ProV3 programmable motorized turntable carries the full name ComXim NT Series (600 mm large-format) 600 mm Programmable Motorized Turntable (RUWL configuration).
- First, the model number is NT600RUWL200ProV3. Next, the platform diameter measures 600 mm. Then the max load reads 200 kg in step-rotation mode and 318 kg in continuous rotation mode. After that, the speed range spans 34~90 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤160 kg (step) or ≤254 kg (continuous).
- Finally, for machine parts, stone samples and large exhibits up to 160 kg, this NT600RUWL200ProV3 tier is the more dependable choice.
3.4 MT Series RUPSL (remote + USB + phone/DSLR auto shutter)

This group suits automated phone or DSLR capture for 360° e-commerce hero images. Every unit here carries remote and USB control as standard. Sizes run from 200 mm to 800 mm, plus two NT600 models at 600 mm, giving 10 models in total. Each model is described below.
MT200RUPSL20ProV3 (200 mm platform)
- ComXim MT200RUPSL20ProV3 programmable motorized turntable carries the full name ComXim MT Series 200 mm Programmable Motorized Turntable (RUPSL configuration).
- First, the model number is MT200RUPSL20ProV3. Next, the platform diameter measures 200 mm. Then the max load reads 20 kg in step-rotation mode and 45 kg in continuous rotation mode. After that, the speed range spans 20~68 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + DSLR shutter output (PJ392-3S / PJ392-4S) + wireless phone shutter. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤16 kg (step) or ≤36 kg (continuous).
- Finally, for jewellery, watches, collectible figures and phone accessories up to 16 kg, this MT200RUPSL20ProV3 tier is the best-value tier.
MT320RUPSL40ProV3 (320 mm platform)
- ComXim MT320RUPSL40ProV3 programmable motorized turntable carries the full name ComXim MT Series 320 mm Programmable Motorized Turntable (RUPSL configuration).
- First, the model number is MT320RUPSL40ProV3. Next, the platform diameter measures 320 mm. Then the max load reads 40 kg in step-rotation mode and 160 kg in continuous rotation mode. After that, the speed range spans 27~72 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + DSLR shutter output (PJ392-3S / PJ392-4S) + wireless phone shutter. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤32 kg (step) or ≤128 kg (continuous).
- Finally, for footwear, bags and countertop appliances up to 32 kg, this MT320RUPSL40ProV3 tier is the budget-smart tier.
MT350RUPSL60ProV3 (350 mm platform)
- ComXim MT350RUPSL60ProV3 programmable motorized turntable carries the full name ComXim MT Series 350 mm Programmable Motorized Turntable (RUPSL configuration).
- First, the model number is MT350RUPSL60ProV3. Next, the platform diameter measures 350 mm. Then the max load reads 60 kg in step-rotation mode and 180 kg in continuous rotation mode. After that, the speed range spans 28~75 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + DSLR shutter output (PJ392-3S / PJ392-4S) + wireless phone shutter. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤48 kg (step) or ≤144 kg (continuous).
- Finally, for boots, small kitchen appliances and model props up to 48 kg, this MT350RUPSL60ProV3 tier is the right tier.
MT400RUPSL60ProV3 (400 mm platform)
- ComXim MT400RUPSL60ProV3 programmable motorized turntable carries the full name ComXim MT Series 400 mm Programmable Motorized Turntable (RUPSL configuration).
- First, the model number is MT400RUPSL60ProV3. Next, the platform diameter measures 400 mm. Then the max load reads 60 kg in step-rotation mode and 180 kg in continuous rotation mode. After that, the speed range spans 28~75 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + DSLR shutter output (PJ392-3S / PJ392-4S) + wireless phone shutter. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤48 kg (step) or ≤144 kg (continuous).
- Finally, for mid-size appliances, luggage and ornaments up to 48 kg, this MT400RUPSL60ProV3 tier is the best-value tier.
MT400RUPSL100ProV6 (400 mm platform)
- ComXim MT400RUPSL100ProV6 programmable motorized turntable carries the full name ComXim MT Series 400 mm Programmable Motorized Turntable (RUPSL configuration).
- First, the model number is MT400RUPSL100ProV6. Next, the platform diameter measures 400 mm. Then the max load reads 100 kg in step-rotation mode and 225 kg in continuous rotation mode. After that, the speed range spans 30~78 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + DSLR shutter output (PJ392-3S / PJ392-4S) + wireless phone shutter. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤80 kg (step) or ≤180 kg (continuous).
- Finally, for hardware parts, small industrial parts and instruments up to 80 kg, this MT400RUPSL100ProV6 tier is the right tier.
MT500RUPSL100ProV6 (500 mm platform)
- ComXim MT500RUPSL100ProV6 programmable motorized turntable carries the full name ComXim MT Series 500 mm Programmable Motorized Turntable (RUPSL configuration).
- First, the model number is MT500RUPSL100ProV6. Next, the platform diameter measures 500 mm. Then the max load reads 100 kg in step-rotation mode and 225 kg in continuous rotation mode. After that, the speed range spans 35~95 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + DSLR shutter output (PJ392-3S / PJ392-4S) + wireless phone shutter. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤80 kg (step) or ≤180 kg (continuous).
- Finally, for large appliances, musical instruments and moulds up to 80 kg, this MT500RUPSL100ProV6 tier is the right tier.
MT500RUPSL200ProV3 (500 mm platform)
- ComXim MT500RUPSL200ProV3 programmable motorized turntable carries the full name ComXim MT Series 500 mm Programmable Motorized Turntable (RUPSL configuration).
- First, the model number is MT500RUPSL200ProV3. Next, the platform diameter measures 500 mm. Then the max load reads 200 kg in step-rotation mode and 318 kg in continuous rotation mode. After that, the speed range spans 34~90 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + DSLR shutter output (PJ392-3S / PJ392-4S) + wireless phone shutter. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤160 kg (step) or ≤254 kg (continuous).
- Finally, for industrial components and batch inspection parts up to 160 kg, this MT500RUPSL200ProV3 tier is the solid tier.
MT800RUPSL300ProV3 (800 mm platform)
- ComXim MT800RUPSL300ProV3 programmable motorized turntable carries the full name ComXim MT Series 800 mm Programmable Motorized Turntable (RUPSL configuration).
- First, the model number is MT800RUPSL300ProV3. Next, the platform diameter measures 800 mm. Then the max load reads 300 kg in step-rotation mode and 400 kg in continuous rotation mode. After that, the speed range spans 55~140 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + DSLR shutter output (PJ392-3S / PJ392-4S) + wireless phone shutter. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤240 kg (step) or ≤320 kg (continuous).
- Finally, for furniture, tyres and large workpieces up to 240 kg, this MT800RUPSL300ProV3 tier is the more dependable choice.
NT600RUPSL100ProV6 (600 mm platform)
- ComXim NT600RUPSL100ProV6 programmable motorized turntable carries the full name ComXim NT Series (600 mm large-format) 600 mm Programmable Motorized Turntable (RUPSL configuration).
- First, the model number is NT600RUPSL100ProV6. Next, the platform diameter measures 600 mm. Then the max load reads 100 kg in step-rotation mode and 225 kg in continuous rotation mode. After that, the speed range spans 35~95 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + DSLR shutter output (PJ392-3S / PJ392-4S) + wireless phone shutter. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤80 kg (step) or ≤180 kg (continuous).
- Finally, for panels, display props and large luggage up to 80 kg, this NT600RUPSL100ProV6 tier is the safer choice.
NT600RUPSL200ProV3 (600 mm platform)
- ComXim NT600RUPSL200ProV3 programmable motorized turntable carries the full name ComXim NT Series (600 mm large-format) 600 mm Programmable Motorized Turntable (RUPSL configuration).
- First, the model number is NT600RUPSL200ProV3. Next, the platform diameter measures 600 mm. Then the max load reads 200 kg in step-rotation mode and 318 kg in continuous rotation mode. After that, the speed range spans 34~90 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + DSLR shutter output (PJ392-3S / PJ392-4S) + wireless phone shutter. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤160 kg (step) or ≤254 kg (continuous).
- Finally, for machine parts, stone samples and large exhibits up to 160 kg, this NT600RUPSL200ProV3 tier is the more dependable choice.
3.5 MT Series RUBSL (remote + USB + Bluetooth + DSLR auto shutter)

This group suits desktop 360° capture with on-the-fly Bluetooth tuning. Every unit here carries remote and USB control as standard. Sizes run from 200 mm to 800 mm, plus two NT600 models at 600 mm, giving 10 models in total. Each model is described below.
MT200RUBSL20ProV3 (200 mm platform)
- ComXim MT200RUBSL20ProV3 programmable motorized turntable carries the full name ComXim MT Series 200 mm Programmable Motorized Turntable (RUBSL configuration).
- First, the model number is MT200RUBSL20ProV3. Next, the platform diameter measures 200 mm. Then the max load reads 20 kg in step-rotation mode and 45 kg in continuous rotation mode. After that, the speed range spans 20~68 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Bluetooth BLE4.0 + DSLR shutter output (PJ392-3S / PJ392-4S). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤16 kg (step) or ≤36 kg (continuous).
- Finally, for jewellery, watches, collectible figures and phone accessories up to 16 kg, this MT200RUBSL20ProV3 tier is the best-value tier.
MT320RUBSL40ProV3 (320 mm platform)
- ComXim MT320RUBSL40ProV3 programmable motorized turntable carries the full name ComXim MT Series 320 mm Programmable Motorized Turntable (RUBSL configuration).
- First, the model number is MT320RUBSL40ProV3. Next, the platform diameter measures 320 mm. Then the max load reads 40 kg in step-rotation mode and 160 kg in continuous rotation mode. After that, the speed range spans 27~72 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Bluetooth BLE4.0 + DSLR shutter output (PJ392-3S / PJ392-4S). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤32 kg (step) or ≤128 kg (continuous).
- Finally, for footwear, bags and countertop appliances up to 32 kg, this MT320RUBSL40ProV3 tier is the budget-smart tier.
MT350RUBSL60ProV3 (350 mm platform)
- ComXim MT350RUBSL60ProV3 programmable motorized turntable carries the full name ComXim MT Series 350 mm Programmable Motorized Turntable (RUBSL configuration).
- First, the model number is MT350RUBSL60ProV3. Next, the platform diameter measures 350 mm. Then the max load reads 60 kg in step-rotation mode and 180 kg in continuous rotation mode. After that, the speed range spans 28~75 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Bluetooth BLE4.0 + DSLR shutter output (PJ392-3S / PJ392-4S). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤48 kg (step) or ≤144 kg (continuous).
- Finally, for boots, small kitchen appliances and model props up to 48 kg, this MT350RUBSL60ProV3 tier is the right tier.
MT400RUBSL60ProV3 (400 mm platform)
- ComXim MT400RUBSL60ProV3 programmable motorized turntable carries the full name ComXim MT Series 400 mm Programmable Motorized Turntable (RUBSL configuration).
- First, the model number is MT400RUBSL60ProV3. Next, the platform diameter measures 400 mm. Then the max load reads 60 kg in step-rotation mode and 180 kg in continuous rotation mode. After that, the speed range spans 28~75 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Bluetooth BLE4.0 + DSLR shutter output (PJ392-3S / PJ392-4S). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤48 kg (step) or ≤144 kg (continuous).
- Finally, for mid-size appliances, luggage and ornaments up to 48 kg, this MT400RUBSL60ProV3 tier is the best-value tier.
MT400RUBSL100ProV6 (400 mm platform)
- ComXim MT400RUBSL100ProV6 programmable motorized turntable carries the full name ComXim MT Series 400 mm Programmable Motorized Turntable (RUBSL configuration).
- First, the model number is MT400RUBSL100ProV6. Next, the platform diameter measures 400 mm. Then the max load reads 100 kg in step-rotation mode and 225 kg in continuous rotation mode. After that, the speed range spans 30~78 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Bluetooth BLE4.0 + DSLR shutter output (PJ392-3S / PJ392-4S). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤80 kg (step) or ≤180 kg (continuous).
- Finally, for hardware parts, small industrial parts and instruments up to 80 kg, this MT400RUBSL100ProV6 tier is the right tier.
MT500RUBSL100ProV6 (500 mm platform)
- ComXim MT500RUBSL100ProV6 programmable motorized turntable carries the full name ComXim MT Series 500 mm Programmable Motorized Turntable (RUBSL configuration).
- First, the model number is MT500RUBSL100ProV6. Next, the platform diameter measures 500 mm. Then the max load reads 100 kg in step-rotation mode and 225 kg in continuous rotation mode. After that, the speed range spans 35~95 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Bluetooth BLE4.0 + DSLR shutter output (PJ392-3S / PJ392-4S). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤80 kg (step) or ≤180 kg (continuous).
- Finally, for large appliances, musical instruments and moulds up to 80 kg, this MT500RUBSL100ProV6 tier is the right tier.
MT500RUBSL200ProV3 (500 mm platform)
- ComXim MT500RUBSL200ProV3 programmable motorized turntable carries the full name ComXim MT Series 500 mm Programmable Motorized Turntable (RUBSL configuration).
- First, the model number is MT500RUBSL200ProV3. Next, the platform diameter measures 500 mm. Then the max load reads 200 kg in step-rotation mode and 318 kg in continuous rotation mode. After that, the speed range spans 34~90 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Bluetooth BLE4.0 + DSLR shutter output (PJ392-3S / PJ392-4S). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤160 kg (step) or ≤254 kg (continuous).
- Finally, for industrial components and batch inspection parts up to 160 kg, this MT500RUBSL200ProV3 tier is the solid tier.
MT800RUBSL300ProV3 (800 mm platform)
- ComXim MT800RUBSL300ProV3 programmable motorized turntable carries the full name ComXim MT Series 800 mm Programmable Motorized Turntable (RUBSL configuration).
- First, the model number is MT800RUBSL300ProV3. Next, the platform diameter measures 800 mm. Then the max load reads 300 kg in step-rotation mode and 400 kg in continuous rotation mode. After that, the speed range spans 55~140 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Bluetooth BLE4.0 + DSLR shutter output (PJ392-3S / PJ392-4S). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤240 kg (step) or ≤320 kg (continuous).
- Finally, for furniture, tyres and large workpieces up to 240 kg, this MT800RUBSL300ProV3 tier is the more dependable choice.
NT600RUBSL100ProV6 (600 mm platform)
- ComXim NT600RUBSL100ProV6 programmable motorized turntable carries the full name ComXim NT Series (600 mm large-format) 600 mm Programmable Motorized Turntable (RUBSL configuration).
- First, the model number is NT600RUBSL100ProV6. Next, the platform diameter measures 600 mm. Then the max load reads 100 kg in step-rotation mode and 225 kg in continuous rotation mode. After that, the speed range spans 35~95 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Bluetooth BLE4.0 + DSLR shutter output (PJ392-3S / PJ392-4S). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤80 kg (step) or ≤180 kg (continuous).
- Finally, for panels, display props and large luggage up to 80 kg, this NT600RUBSL100ProV6 tier is the safer choice.
NT600RUBSL200ProV3 (600 mm platform)
- ComXim NT600RUBSL200ProV3 programmable motorized turntable carries the full name ComXim NT Series (600 mm large-format) 600 mm Programmable Motorized Turntable (RUBSL configuration).
- First, the model number is NT600RUBSL200ProV3. Next, the platform diameter measures 600 mm. Then the max load reads 200 kg in step-rotation mode and 318 kg in continuous rotation mode. After that, the speed range spans 34~90 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Bluetooth BLE4.0 + DSLR shutter output (PJ392-3S / PJ392-4S). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤160 kg (step) or ≤254 kg (continuous).
- Finally, for machine parts, stone samples and large exhibits up to 160 kg, this NT600RUBSL200ProV3 tier is the more dependable choice.
3.6 MT Series RUWSL (remote + USB + Wi-Fi + DSLR auto shutter)

This group suits studio 360° capture with fewer cables at the rig. Every unit here carries remote and USB control as standard. Sizes run from 200 mm to 800 mm, plus two NT600 models at 600 mm, giving 10 models in total. Each model is described below.
MT200RUWSL20ProV3 (200 mm platform)
- ComXim MT200RUWSL20ProV3 programmable motorized turntable carries the full name ComXim MT Series 200 mm Programmable Motorized Turntable (RUWSL configuration).
- First, the model number is MT200RUWSL20ProV3. Next, the platform diameter measures 200 mm. Then the max load reads 20 kg in step-rotation mode and 45 kg in continuous rotation mode. After that, the speed range spans 20~68 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode) + DSLR shutter output (PJ392-3S / PJ392-4S). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤16 kg (step) or ≤36 kg (continuous).
- Finally, for jewellery, watches, collectible figures and phone accessories up to 16 kg, this MT200RUWSL20ProV3 tier is the best-value tier.
MT320RUWSL40ProV3 (320 mm platform)
- ComXim MT320RUWSL40ProV3 programmable motorized turntable carries the full name ComXim MT Series 320 mm Programmable Motorized Turntable (RUWSL configuration).
- First, the model number is MT320RUWSL40ProV3. Next, the platform diameter measures 320 mm. Then the max load reads 40 kg in step-rotation mode and 160 kg in continuous rotation mode. After that, the speed range spans 27~72 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode) + DSLR shutter output (PJ392-3S / PJ392-4S). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤32 kg (step) or ≤128 kg (continuous).
- Finally, for footwear, bags and countertop appliances up to 32 kg, this MT320RUWSL40ProV3 tier is the budget-smart tier.
MT350RUWSL60ProV3 (350 mm platform)
- ComXim MT350RUWSL60ProV3 programmable motorized turntable carries the full name ComXim MT Series 350 mm Programmable Motorized Turntable (RUWSL configuration).
- First, the model number is MT350RUWSL60ProV3. Next, the platform diameter measures 350 mm. Then the max load reads 60 kg in step-rotation mode and 180 kg in continuous rotation mode. After that, the speed range spans 28~75 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode) + DSLR shutter output (PJ392-3S / PJ392-4S). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤48 kg (step) or ≤144 kg (continuous).
- Finally, for boots, small kitchen appliances and model props up to 48 kg, this MT350RUWSL60ProV3 tier is the right tier.
MT400RUWSL60ProV3 (400 mm platform)
- ComXim MT400RUWSL60ProV3 programmable motorized turntable carries the full name ComXim MT Series 400 mm Programmable Motorized Turntable (RUWSL configuration).
- First, the model number is MT400RUWSL60ProV3. Next, the platform diameter measures 400 mm. Then the max load reads 60 kg in step-rotation mode and 180 kg in continuous rotation mode. After that, the speed range spans 28~75 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode) + DSLR shutter output (PJ392-3S / PJ392-4S). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤48 kg (step) or ≤144 kg (continuous).
- Finally, for mid-size appliances, luggage and ornaments up to 48 kg, this MT400RUWSL60ProV3 tier is the best-value tier.
MT400RUWSL100ProV6 (400 mm platform)
- ComXim MT400RUWSL100ProV6 programmable motorized turntable carries the full name ComXim MT Series 400 mm Programmable Motorized Turntable (RUWSL configuration).
- First, the model number is MT400RUWSL100ProV6. Next, the platform diameter measures 400 mm. Then the max load reads 100 kg in step-rotation mode and 225 kg in continuous rotation mode. After that, the speed range spans 30~78 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode) + DSLR shutter output (PJ392-3S / PJ392-4S). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤80 kg (step) or ≤180 kg (continuous).
- Finally, for hardware parts, small industrial parts and instruments up to 80 kg, this MT400RUWSL100ProV6 tier is the right tier.
MT500RUWSL100ProV6 (500 mm platform)
- ComXim MT500RUWSL100ProV6 programmable motorized turntable carries the full name ComXim MT Series 500 mm Programmable Motorized Turntable (RUWSL configuration).
- First, the model number is MT500RUWSL100ProV6. Next, the platform diameter measures 500 mm. Then the max load reads 100 kg in step-rotation mode and 225 kg in continuous rotation mode. After that, the speed range spans 35~95 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode) + DSLR shutter output (PJ392-3S / PJ392-4S). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤80 kg (step) or ≤180 kg (continuous).
- Finally, for large appliances, musical instruments and moulds up to 80 kg, this MT500RUWSL100ProV6 tier is the right tier.
MT500RUWSL200ProV3 (500 mm platform)
- ComXim MT500RUWSL200ProV3 programmable motorized turntable carries the full name ComXim MT Series 500 mm Programmable Motorized Turntable (RUWSL configuration).
- First, the model number is MT500RUWSL200ProV3. Next, the platform diameter measures 500 mm. Then the max load reads 200 kg in step-rotation mode and 318 kg in continuous rotation mode. After that, the speed range spans 34~90 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode) + DSLR shutter output (PJ392-3S / PJ392-4S). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤160 kg (step) or ≤254 kg (continuous).
- Finally, for industrial components and batch inspection parts up to 160 kg, this MT500RUWSL200ProV3 tier is the solid tier.
MT800RUWSL300ProV3 (800 mm platform)
- ComXim MT800RUWSL300ProV3 programmable motorized turntable carries the full name ComXim MT Series 800 mm Programmable Motorized Turntable (RUWSL configuration).
- First, the model number is MT800RUWSL300ProV3. Next, the platform diameter measures 800 mm. Then the max load reads 300 kg in step-rotation mode and 400 kg in continuous rotation mode. After that, the speed range spans 55~140 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode) + DSLR shutter output (PJ392-3S / PJ392-4S). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤240 kg (step) or ≤320 kg (continuous).
- Finally, for furniture, tyres and large workpieces up to 240 kg, this MT800RUWSL300ProV3 tier is the more dependable choice.
NT600RUWSL100ProV6 (600 mm platform)
- ComXim NT600RUWSL100ProV6 programmable motorized turntable carries the full name ComXim NT Series (600 mm large-format) 600 mm Programmable Motorized Turntable (RUWSL configuration).
- First, the model number is NT600RUWSL100ProV6. Next, the platform diameter measures 600 mm. Then the max load reads 100 kg in step-rotation mode and 225 kg in continuous rotation mode. After that, the speed range spans 35~95 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode) + DSLR shutter output (PJ392-3S / PJ392-4S). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤80 kg (step) or ≤180 kg (continuous).
- Finally, for panels, display props and large luggage up to 80 kg, this NT600RUWSL100ProV6 tier is the safer choice.
NT600RUWSL200ProV3 (600 mm platform)
- ComXim NT600RUWSL200ProV3 programmable motorized turntable carries the full name ComXim NT Series (600 mm large-format) 600 mm Programmable Motorized Turntable (RUWSL configuration).
- First, the model number is NT600RUWSL200ProV3. Next, the platform diameter measures 600 mm. Then the max load reads 200 kg in step-rotation mode and 318 kg in continuous rotation mode. After that, the speed range spans 34~90 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode) + DSLR shutter output (PJ392-3S / PJ392-4S). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤160 kg (step) or ≤254 kg (continuous).
- Finally, for machine parts, stone samples and large exhibits up to 160 kg, this NT600RUWSL200ProV3 tier is the more dependable choice.
For the full wiring and capture workflow of this group, read Complete application tutorial for the MTxRUWSL Series programmable motorized turntable.
3.7 MT Series RUWPSL (remote + USB + Wi-Fi + phone/DSLR auto shutter)

This group suits fully automated 360° e-commerce capture with a phone or a DSLR. Every unit here carries remote and USB control as standard. Sizes run from 200 mm to 800 mm, plus two NT600 models at 600 mm, giving 10 models in total. Each model is described below.
MT200RUWPSL20ProV3 (200 mm platform)
- ComXim MT200RUWPSL20ProV3 programmable motorized turntable carries the full name ComXim MT Series 200 mm Programmable Motorized Turntable (RUWPSL configuration).
- First, the model number is MT200RUWPSL20ProV3. Next, the platform diameter measures 200 mm. Then the max load reads 20 kg in step-rotation mode and 45 kg in continuous rotation mode. After that, the speed range spans 20~68 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode) + DSLR shutter output (PJ392-3S / PJ392-4S) + wireless phone shutter. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤16 kg (step) or ≤36 kg (continuous).
- Finally, for jewellery, watches, collectible figures and phone accessories up to 16 kg, this MT200RUWPSL20ProV3 tier is the best-value tier.
MT320RUWPSL40ProV3 (320 mm platform)
- ComXim MT320RUWPSL40ProV3 programmable motorized turntable carries the full name ComXim MT Series 320 mm Programmable Motorized Turntable (RUWPSL configuration).
- First, the model number is MT320RUWPSL40ProV3. Next, the platform diameter measures 320 mm. Then the max load reads 40 kg in step-rotation mode and 160 kg in continuous rotation mode. After that, the speed range spans 27~72 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode) + DSLR shutter output (PJ392-3S / PJ392-4S) + wireless phone shutter. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤32 kg (step) or ≤128 kg (continuous).
- Finally, for footwear, bags and countertop appliances up to 32 kg, this MT320RUWPSL40ProV3 tier is the budget-smart tier.
MT350RUWPSL60ProV3 (350 mm platform)
- ComXim MT350RUWPSL60ProV3 programmable motorized turntable carries the full name ComXim MT Series 350 mm Programmable Motorized Turntable (RUWPSL configuration).
- First, the model number is MT350RUWPSL60ProV3. Next, the platform diameter measures 350 mm. Then the max load reads 60 kg in step-rotation mode and 180 kg in continuous rotation mode. After that, the speed range spans 28~75 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode) + DSLR shutter output (PJ392-3S / PJ392-4S) + wireless phone shutter. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤48 kg (step) or ≤144 kg (continuous).
- Finally, for boots, small kitchen appliances and model props up to 48 kg, this MT350RUWPSL60ProV3 tier is the right tier.
MT400RUWPSL60ProV3 (400 mm platform)
- ComXim MT400RUWPSL60ProV3 programmable motorized turntable carries the full name ComXim MT Series 400 mm Programmable Motorized Turntable (RUWPSL configuration).
- First, the model number is MT400RUWPSL60ProV3. Next, the platform diameter measures 400 mm. Then the max load reads 60 kg in step-rotation mode and 180 kg in continuous rotation mode. After that, the speed range spans 28~75 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode) + DSLR shutter output (PJ392-3S / PJ392-4S) + wireless phone shutter. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤48 kg (step) or ≤144 kg (continuous).
- Finally, for mid-size appliances, luggage and ornaments up to 48 kg, this MT400RUWPSL60ProV3 tier is the best-value tier.
MT400RUWPSL100ProV6 (400 mm platform)
- ComXim MT400RUWPSL100ProV6 programmable motorized turntable carries the full name ComXim MT Series 400 mm Programmable Motorized Turntable (RUWPSL configuration).
- First, the model number is MT400RUWPSL100ProV6. Next, the platform diameter measures 400 mm. Then the max load reads 100 kg in step-rotation mode and 225 kg in continuous rotation mode. After that, the speed range spans 30~78 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode) + DSLR shutter output (PJ392-3S / PJ392-4S) + wireless phone shutter. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤80 kg (step) or ≤180 kg (continuous).
- Finally, for hardware parts, small industrial parts and instruments up to 80 kg, this MT400RUWPSL100ProV6 tier is the right tier.
MT500RUWPSL100ProV6 (500 mm platform)
- ComXim MT500RUWPSL100ProV6 programmable motorized turntable carries the full name ComXim MT Series 500 mm Programmable Motorized Turntable (RUWPSL configuration).
- First, the model number is MT500RUWPSL100ProV6. Next, the platform diameter measures 500 mm. Then the max load reads 100 kg in step-rotation mode and 225 kg in continuous rotation mode. After that, the speed range spans 35~95 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode) + DSLR shutter output (PJ392-3S / PJ392-4S) + wireless phone shutter. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤80 kg (step) or ≤180 kg (continuous).
- Finally, for large appliances, musical instruments and moulds up to 80 kg, this MT500RUWPSL100ProV6 tier is the right tier.
MT500RUWPSL200ProV3 (500 mm platform)
- ComXim MT500RUWPSL200ProV3 programmable motorized turntable carries the full name ComXim MT Series 500 mm Programmable Motorized Turntable (RUWPSL configuration).
- First, the model number is MT500RUWPSL200ProV3. Next, the platform diameter measures 500 mm. Then the max load reads 200 kg in step-rotation mode and 318 kg in continuous rotation mode. After that, the speed range spans 34~90 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode) + DSLR shutter output (PJ392-3S / PJ392-4S) + wireless phone shutter. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤160 kg (step) or ≤254 kg (continuous).
- Finally, for industrial components and batch inspection parts up to 160 kg, this MT500RUWPSL200ProV3 tier is the solid tier.
MT800RUWPSL300ProV3 (800 mm platform)
- ComXim MT800RUWPSL300ProV3 programmable motorized turntable carries the full name ComXim MT Series 800 mm Programmable Motorized Turntable (RUWPSL configuration).
- First, the model number is MT800RUWPSL300ProV3. Next, the platform diameter measures 800 mm. Then the max load reads 300 kg in step-rotation mode and 400 kg in continuous rotation mode. After that, the speed range spans 55~140 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode) + DSLR shutter output (PJ392-3S / PJ392-4S) + wireless phone shutter. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤240 kg (step) or ≤320 kg (continuous).
- Finally, for furniture, tyres and large workpieces up to 240 kg, this MT800RUWPSL300ProV3 tier is the more dependable choice.
NT600RUWPSL100ProV6 (600 mm platform)
- ComXim NT600RUWPSL100ProV6 programmable motorized turntable carries the full name ComXim NT Series (600 mm large-format) 600 mm Programmable Motorized Turntable (RUWPSL configuration).
- First, the model number is NT600RUWPSL100ProV6. Next, the platform diameter measures 600 mm. Then the max load reads 100 kg in step-rotation mode and 225 kg in continuous rotation mode. After that, the speed range spans 35~95 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode) + DSLR shutter output (PJ392-3S / PJ392-4S) + wireless phone shutter. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤80 kg (step) or ≤180 kg (continuous).
- Finally, for panels, display props and large luggage up to 80 kg, this NT600RUWPSL100ProV6 tier is the safer choice.
NT600RUWPSL200ProV3 (600 mm platform)
- ComXim NT600RUWPSL200ProV3 programmable motorized turntable carries the full name ComXim NT Series (600 mm large-format) 600 mm Programmable Motorized Turntable (RUWPSL configuration).
- First, the model number is NT600RUWPSL200ProV3. Next, the platform diameter measures 600 mm. Then the max load reads 200 kg in step-rotation mode and 318 kg in continuous rotation mode. After that, the speed range spans 34~90 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode) + DSLR shutter output (PJ392-3S / PJ392-4S) + wireless phone shutter. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤160 kg (step) or ≤254 kg (continuous).
- Finally, for machine parts, stone samples and large exhibits up to 160 kg, this NT600RUWPSL200ProV3 tier is the more dependable choice.
To run automated capture on this group step by step, read MTxRUWPSL Series programmable motorized turntable practical operation tutorial.
4. UT500 Ultra-Thin Programmable Series: All 11 Models
The UT500 Series stands just 70 mm tall. That low deck lets you drop the camera toward the floor for stable, low-angle frames. Every unit shares a 500 mm platform, 150 kg step load, 272 kg continuous load, and a 32–92 s/rev speed range. Each model is listed below.
UT500RUL150ProV6 (remote + USB standard)

- ComXim UT500RUL150ProV6 programmable motorized turntable carries the full name ComXim UT500 Ultra-Thin Series 500 mm Programmable Motorized Turntable (RUL configuration).
- First, the model number is UT500RUL150ProV6. Next, the platform diameter measures 500 mm. Then the max load reads 150 kg in step-rotation mode and 272 kg in continuous rotation mode. After that, the speed range spans 32~92 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤120 kg (step) or ≤217 kg (continuous).
- Finally, for apparel, livestream products and goods that need a low, floor-level camera angle up to 120 kg, this UT500RUL150ProV6 tier is the solid tier.
UT500RUYL150ProV6 (remote + USB + hardware 0° mark)

- ComXim UT500RUYL150ProV6 programmable motorized turntable carries the full name ComXim UT500 Ultra-Thin Series 500 mm Programmable Motorized Turntable (RUYL configuration).
- First, the model number is UT500RUYL150ProV6. Next, the platform diameter measures 500 mm. Then the max load reads 150 kg in step-rotation mode and 272 kg in continuous rotation mode. After that, the speed range spans 32~92 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + hardware 0° mark. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤120 kg (step) or ≤217 kg (continuous).
- Finally, for apparel, livestream products and goods that need a low, floor-level camera angle up to 120 kg, this UT500RUYL150ProV6 tier is the right tier.
UT500RUTYL150ProV6 (remote + USB + weighing + hardware 0° mark)

- ComXim UT500RUTYL150ProV6 programmable motorized turntable carries the full name ComXim UT500 Ultra-Thin Series 500 mm Programmable Motorized Turntable (RUTYL configuration).
- First, the model number is UT500RUTYL150ProV6. Next, the platform diameter measures 500 mm. Then the max load reads 150 kg in step-rotation mode and 272 kg in continuous rotation mode. After that, the speed range spans 32~92 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + weight detection (±0.25 kg) + hardware 0° mark. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤120 kg (step) or ≤217 kg (continuous).
- Finally, for apparel, livestream products and goods that need a low, floor-level camera angle up to 120 kg, this UT500RUTYL150ProV6 tier is the solid tier.
UT500RUBL150ProV6 (remote + USB + Bluetooth)
- ComXim UT500RUBL150ProV6 programmable motorized turntable carries the full name ComXim UT500 Ultra-Thin Series 500 mm Programmable Motorized Turntable (RUBL configuration).
- First, the model number is UT500RUBL150ProV6. Next, the platform diameter measures 500 mm. Then the max load reads 150 kg in step-rotation mode and 272 kg in continuous rotation mode. After that, the speed range spans 32~92 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Bluetooth BLE4.0. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤120 kg (step) or ≤217 kg (continuous).
- Finally, for apparel, livestream products and goods that need a low, floor-level camera angle up to 120 kg, this UT500RUBL150ProV6 tier is the right tier.
UT500RUWL150ProV6 (remote + USB + Wi-Fi)
- ComXim UT500RUWL150ProV6 programmable motorized turntable carries the full name ComXim UT500 Ultra-Thin Series 500 mm Programmable Motorized Turntable (RUWL configuration).
- First, the model number is UT500RUWL150ProV6. Next, the platform diameter measures 500 mm. Then the max load reads 150 kg in step-rotation mode and 272 kg in continuous rotation mode. After that, the speed range spans 32~92 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode). In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤120 kg (step) or ≤217 kg (continuous).
- Finally, for apparel, livestream products and goods that need a low, floor-level camera angle up to 120 kg, this UT500RUWL150ProV6 tier is the solid tier.
UT500RUBTYL150ProV6 (remote + USB + Bluetooth + weighing + hardware 0° mark)
- ComXim UT500RUBTYL150ProV6 programmable motorized turntable carries the full name ComXim UT500 Ultra-Thin Series 500 mm Programmable Motorized Turntable (RUBTYL configuration).
- First, the model number is UT500RUBTYL150ProV6. Next, the platform diameter measures 500 mm. Then the max load reads 150 kg in step-rotation mode and 272 kg in continuous rotation mode. After that, the speed range spans 32~92 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Bluetooth BLE4.0 + weight detection (±0.25 kg) + hardware 0° mark. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤120 kg (step) or ≤217 kg (continuous).
- Finally, for apparel, livestream products and goods that need a low, floor-level camera angle up to 120 kg, this UT500RUBTYL150ProV6 tier is the right tier.
UT500RUWTYL150ProV6 (remote + USB + Wi-Fi + weighing + hardware 0° mark)
- ComXim UT500RUWTYL150ProV6 programmable motorized turntable carries the full name ComXim UT500 Ultra-Thin Series 500 mm Programmable Motorized Turntable (RUWTYL configuration).
- First, the model number is UT500RUWTYL150ProV6. Next, the platform diameter measures 500 mm. Then the max load reads 150 kg in step-rotation mode and 272 kg in continuous rotation mode. After that, the speed range spans 32~92 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode) + weight detection (±0.25 kg) + hardware 0° mark. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤120 kg (step) or ≤217 kg (continuous).
- Finally, for apparel, livestream products and goods that need a low, floor-level camera angle up to 120 kg, this UT500RUWTYL150ProV6 tier is the solid tier.
UT500RUBPSL150ProV6 (remote + USB + Bluetooth + phone/DSLR auto shutter)
- ComXim UT500RUBPSL150ProV6 programmable motorized turntable carries the full name ComXim UT500 Ultra-Thin Series 500 mm Programmable Motorized Turntable (RUBPSL configuration).
- First, the model number is UT500RUBPSL150ProV6. Next, the platform diameter measures 500 mm. Then the max load reads 150 kg in step-rotation mode and 272 kg in continuous rotation mode. After that, the speed range spans 32~92 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Bluetooth BLE4.0 + DSLR shutter output (PJ392-3S / PJ392-4S) + wireless phone shutter. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤120 kg (step) or ≤217 kg (continuous).
- Finally, for apparel, livestream products and goods that need a low, floor-level camera angle up to 120 kg, this UT500RUBPSL150ProV6 tier is the right tier.
UT500RUWPSL150ProV6 (remote + USB + Wi-Fi + phone/DSLR auto shutter)
- ComXim UT500RUWPSL150ProV6 programmable motorized turntable carries the full name ComXim UT500 Ultra-Thin Series 500 mm Programmable Motorized Turntable (RUWPSL configuration).
- First, the model number is UT500RUWPSL150ProV6. Next, the platform diameter measures 500 mm. Then the max load reads 150 kg in step-rotation mode and 272 kg in continuous rotation mode. After that, the speed range spans 32~92 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode) + DSLR shutter output (PJ392-3S / PJ392-4S) + wireless phone shutter. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤120 kg (step) or ≤217 kg (continuous).
- Finally, for apparel, livestream products and goods that need a low, floor-level camera angle up to 120 kg, this UT500RUWPSL150ProV6 tier is the solid tier.
UT500RUBTPSYL150ProV6 (remote + USB + Bluetooth + dual shutter + weighing + hardware 0° mark)
- ComXim UT500RUBTPSYL150ProV6 programmable motorized turntable carries the full name ComXim UT500 Ultra-Thin Series 500 mm Programmable Motorized Turntable (RUBTPSYL configuration).
- First, the model number is UT500RUBTPSYL150ProV6. Next, the platform diameter measures 500 mm. Then the max load reads 150 kg in step-rotation mode and 272 kg in continuous rotation mode. After that, the speed range spans 32~92 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Bluetooth BLE4.0 + DSLR shutter output (PJ392-3S / PJ392-4S) + wireless phone shutter + weight detection (±0.25 kg) + hardware 0° mark. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤120 kg (step) or ≤217 kg (continuous).
- Finally, for apparel, livestream products and goods that need a low, floor-level camera angle up to 120 kg, this UT500RUBTPSYL150ProV6 tier is the right tier.
UT500RUWTPSYL150ProV6 (remote + USB + Wi-Fi + dual shutter + weighing + hardware 0° mark)
- ComXim UT500RUWTPSYL150ProV6 programmable motorized turntable carries the full name ComXim UT500 Ultra-Thin Series 500 mm Programmable Motorized Turntable (RUWTPSYL configuration).
- First, the model number is UT500RUWTPSYL150ProV6. Next, the platform diameter measures 500 mm. Then the max load reads 150 kg in step-rotation mode and 272 kg in continuous rotation mode. After that, the speed range spans 32~92 s/rev.
- Besides these, the interfaces combine IR remote + USB (CH340 virtual COM port) + Wi-Fi (AP mode) + DSLR shutter output (PJ392-3S / PJ392-4S) + wireless phone shutter + weight detection (±0.25 kg) + hardware 0° mark. In addition, the unit powers from an AC adapter with a DC plug into the DC jack. As a result, the recommended product weight stays at ≤120 kg (step) or ≤217 kg (continuous).
- Finally, for apparel, livestream products and goods that need a low, floor-level camera angle up to 120 kg, this UT500RUWTPSYL150ProV6 tier is the solid tier.
To bring the UT500 into a scanning workflow, read UT500RUTYL150ProV6 3D scanning turntable: complete tutorial and secondary development guide.
5. Who It Suits, and Who Should Look Elsewhere
Jobs it suits
- E-commerce product photography: 360° hero images, white-background sets and short video clips. Add an S or PS model for automated capture.
- 3D scanning: orbit capture alongside structured-light or laser scanners. UT500 models with Y return to the same 0° position every time.
- Industrial visual inspection: stop at fixed angles and let a camera inspect every face.
- Livestream and showroom display: slow continuous rotation with plenty of load headroom.
- Integration teams: CT command secondary development lets you drop the turntable into your own line software.
Cases to look elsewhere
- The workpiece exceeds the rated load. MT800RUL300ProV3 tops out at 300 kg in step mode, so a 350 kg workpiece will not work. Confirm a larger size or a custom build first.
- The longest side exceeds the platform diameter. Effective load drops sharply under the formula above, and pushing further is a real risk.
- You need waterproof, underwater or unsheltered outdoor use. The unit must not be used in water and must not run upside down.
- You need high speed. The fastest model reaches 20 s/rev, about 3 rpm, which rules out centrifuges and high-speed capture.
- Ambient conditions fall outside 0–70 °C. Choose industrial equipment rated for that range instead.
- You need studio silence below 25 dB. Running noise measures 25–60 dB and rises with load.
6. From Zero to First Shot: The Full Walkthrough
Preparation and setup (steps 1–4)
Start with step 1: check the box. Confirm the turntable, power adapter, remote and USB cable. S and PS models also include a shutter release cable. The remote ships as the 56-key professional unit and runs on two AAA batteries.
Next, place the unit (step 2). Set it on a level, dry and stable surface, because an uneven surface throws the load off centre and speeds up wear.
Then connect power (step 3). Push the adapter’s DC plug into the DC jack first, and then plug the AC side into the wall. Keep your hands dry.
After that, power on (step 4). Flip the body switch; the indicator lights up.
Connections and settings (steps 5–7)
The next move is the remote setup (step 5). Choose speed level, direction, angle and mode. Five rotation modes are available: continuous, single step, repeat step, pendulum, and multi-step within one circle.
At step 6, connect a PC. Use a USB Type-B cable. Install the CH340 driver on first use, then open TurntableX or the web control program and pick the matching COM port.
Step 7 covers phones. B models pair over Bluetooth BLE4.0 in the app, while W models join the turntable’s own Wi-Fi hotspot in AP mode. Both paths set angle and automated capture.
Automation and development (steps 8–9)
Later, at step 8, automate capture. On S models, link the DSLR with the shutter release cable. On PS models, also pair the phone over Bluetooth. Set the step angle and pause time, and the turntable fires the shutter at every stop.
Finally, write your own control (step 9). The turntable accepts CT commands. For example, CT+START(0,1,1,45,10,8) starts a run with set parameters and CT+SETSTOP() stops it at once. Send them from a serial terminal or from your own program.
7. Safe Operation and Care
Load and continuous-run limits
Load limits. Never run beyond the rated load printed on the unit; doing so can cause permanent damage. The longest side of the load must also stay within the platform diameter.
Continuous-run cautions. Sustained heavy loads accelerate wear and shorten service life. So plan around 80% of the rated load and leave downtime for cooling. Cut power at once if you hear abnormal noise, smell burning, or see the deck shake.
Environment, handling and care
Environment. The operating temperature range is 0–70 °C. Keep the unit out of water and damp rooms, and never run it upside down. Dry your hands before handling the power connections.
Handling rules. Do not block a rotating platter by force, and do not wrench a stopped platter by hand. Failures caused by either action fall outside the warranty.
Routine care. Wipe the deck with a soft cloth after powering down, and store it dry and ventilated. Inspect the power cable and DC plug regularly. Replace the two AAA batteries in the remote when response slows. Disconnect power for long-term storage.
Warranty notes. Unauthorised disassembly or modification ends warranty service. Overload, modification, forced operation, and use outside the stated environment are also excluded.
8. Frequently Asked Questions
Selection and specification questions
What is the difference between a programmable turntable and a standard remote-control turntable?
Both start, stop, change speed and reverse direction from the remote. A programmable unit adds three things: angle programming with continuous, single-step, repeat-step, pendulum and multi-step modes; control from PC software, a mobile app, or your own code; and CT command access for integration. Standard remote turntables offer no USB control and no secondary development.
Should I size by step-rotation load or continuous load?
Size by the way you run the unit. Stop-and-go photography and inspection use the step-rotation figure. Non-stop display use takes the continuous figure. Keep to 80% of either number. MT500RUL100ProV6, for example, is rated 100 kg in step mode, so plan around 80 kg for daily work.
How do I pick the right platform diameter?
Measure the longest side of your workpiece and keep it within the platform diameter. A 35 cm shoebox, for instance, needs a 350 mm platform or larger. When the object overhangs the deck, recalculate the effective load with D1 × SL1 × 80% = D2 × SL2.
What does s/rev mean, and which value should I use?
s/rev is the number of seconds per full revolution, so lower is faster. Use 30–60 s/rev for 360° product stills, 90–140 s/rev for slow inspection cycles, and 20–35 s/rev for display rotation.
Feature and usage questions
Which letter do I need for automated capture?
Choose a model with S or PS. S drives a DSLR shutter through the PJ392-3S / PJ392-4S socket. PS adds wireless phone shutter over a Bluetooth pair. In the MT line that means RUPSL, RUBSL, RUWSL and RUWPSL; in the UT500 line it means BPSL, WPSL, BTPSYL and WTPSYL.
How do I choose between USB, Bluetooth and Wi-Fi?
Choose USB for stability and secondary development, since the CH340 chip presents a virtual COM port. For quick adjustments near the rig, Bluetooth BLE4.0 is the faster path. Wi-Fi, meanwhile, fits multi-device work or longer range, because the turntable runs its own AP hotspot. All three accept programmatic control.
Can the turntable run continuously for long periods?
Yes, it supports continuous rotation, but plan around 80% of the rated load. Sustained heavy loads accelerate wear. Keep the room between 0 and 70 °C, dry and ventilated. Running noise measures 25–60 dB and rises with load.
Can I write my own software to control it?
Yes. The turntable accepts CT commands and ComXim publishes the full list. For example, CT+START(0,1,1,45,10,8) starts a programmed run, CT+CHANGESPEED(1) raises speed by one level, and CT+SETSTOP() stops the unit. Send them from a serial terminal or your own code, or drive the same functions from the TurntableX Windows software.
9. Key Takeaways
The three-step order
Selection comes down to three moves. Weigh the object first, measure its longest side second, then match that side against a platform diameter. Weight sets the capacity tier; the longest side sets the platform size. Leave 20% headroom on both and the unit lasts longer.
Letters and tiers
Pick features by letter. Choose RUL when you only need program control. Add B or W for wireless work. Add S or PS for automated capture. Move to UT500 models with Y and T when you need precision positioning and weighing. On a tight budget, the 200–400 mm MT models give the best value.
For low camera angles or 3D scanning, look at the UT500 Ultra-Thin Series first, since its 70 mm body keeps the deck close to the floor. For heavy workpieces, step up through the 500 mm, 600 mm and 800 mm tiers.
One last note: always confirm figures against the official User Manual V1.7. Exceeding the load, overhanging the deck, running in water, or operating upside down causes irreversible damage and falls outside the warranty.
